Menu
Get a Quote

Custom

Bearings for cryogenic liquid pumps

Bearings Zhongyue discusses for liquid-oxygen, liquid-nitrogen, LPG, and LNG pumps. Each fluid is a confirmation, with the safety review that fluid requires. It is not a blanket approval.

Two LYZYC angular-contact bearings marked 7309P/P4 and 7309PD7F, the photograph on Zhongyue’s ultra-low-temperature page

Fluids and materials

These bearings are for cryogenic liquid pumps. The media discussed are liquid oxygen, liquid nitrogen, LPG, and LNG, and the pumped liquid may be the lubricant. Naming a fluid is not an approval of your pump, your cleanliness, or the ignition risk. Liquid oxygen in particular needs a separate cleanliness and ignition review: hydrocarbon film is a hazard, not a lubricant.

Variable-frequency motors raise the need for wear resistance and for insulation against current through the bearing. Rings are a high-nitrogen stainless steel of the Cronidur 30 type, with special heat treatment and cold treatment. Balls are hot-isostatic-pressed ceramic, and the raceway is finished to a higher precision. Cold treatment, including a deep treatment near −196°C, is a manufacturing step. It is not the allowable running temperature.

A stated replacement interval is about six times that of a conventional bearing. It is not a guarantee for every fluid, speed, or pump.

The photograph shows two LYZYC angular-contact bearings marked 7309P/P4 and 7309PD7F. Those are the marks on the rings. Dimensions are not given with them, and a standard 7309 size is not assumed. The P4 mark is on that ring. It does not mean every cryogenic-pump bearing is supplied as P4.

Medium named by ZhongyueHow an inquiry has to treat it
LOX, liquid oxygenNamed. Oxygen service needs a cleanliness and ignition review. Hydrocarbon film is a hazard, not a lubricant.
Liquid nitrogenNamed, including as a lubricating medium. Temperature, speed, and the fluid film are confirmed.
LPGNamed. The fluid is flammable. Seals and static are part of the pump design, not a bearing slogan.
LNGNamed later in the text as a lubricating medium. Same rule: confirmed for that pump, not assumed.
Other cryogenic liquidsThe page says “other cryogenic liquid pumps” without listing them. Name the fluid.
A manufacturing cold treatment, including any plant step near −196°C, is not the rated running temperature of the bearing. The fluid’s boiling point is not a bearing rating either.

Product photographs

LYZYC angular-contact bearings marked 7309P/P4 and 7309PD7F on Zhongyue’s ultra-low-temperature bearing page
Photograph on Zhongyue’s ultra-low-temperature page. The rings are marked LYZYC, 7309P/P4 and 7309PD7F. The marking is what the photograph shows. Songju confirms whether that build is the cryogenic-pump execution.

Oxygen, cold fluid, and a motor that can pass current

Liquid oxygen is not “a cold version of oil.” Anything organic — preservative, a grease from a previous assembly, a contaminated glove — is fuel in oxygen. A bearing described for LOX pumps still has to be supplied clean to the standard the pump maker requires, in packaging that does not put the film back on. An oxygen-wetted bearing is not supplied on the strength of this description alone.

Liquid nitrogen and LNG are cold enough that ordinary steels and ordinary clearances change. LPG is flammable and, depending on the component, much less cold than nitrogen; the page groups it with the cryogenic pumps anyway. The bearing has to survive the temperature the pump actually reaches, including cool-down, not a single number copied from a periodic table. The allowable temperature is confirmed for the pump.

The cold treatment in the material sentence is how the rings are processed so the steel is stable. Plants also use a deep treatment around the boiling point of nitrogen as a manufacturing operation. That operation is not the allowable service temperature of the finished bearing. Do not write “rated to −196°C” from this page. It does not say that.

Variable-frequency drives, which Zhongyue mentions, can push current across a bearing and pit the race. Ceramic balls interrupt that path and, because they are hard, they also change the wear picture in a fluid that is a poor lubricant. Both reasons are in the manufacturer’s text. A ceramic ball is not thereby approved for every voltage and every fluid. The insulation requirement belongs in the inquiry.

Lubrication by the pumped liquid means there is no oil film of the kind a spindle bearing expects. The design lives on the fluid’s viscosity at that temperature, on the surface, and on not having a cage or a seal that becomes brittle. None of those details is dimensioned here.

The pump

Send the fluid, the pump speed, the temperature from ambient through cool-down to steady running, the cleanliness standard if the fluid is oxygen, and whether the motor is on a variable-frequency drive. A bearing that is right for liquid nitrogen is not automatically right for oxygen.

The six-times replacement claim stays a manufacturer statement. If you need a maintenance interval, ask for it against your pump. Do not multiply a conventional life by six and call it a calculation.

The address /products/cryogenic-bearings still redirects to the special-purpose page, which keeps an older note and does not replace this one. This category is a different URL.

Handling

For oxygen, agree the cleaning and the bag before anything is touched. A shop wipe with an ordinary solvent can be worse than the preservative it removes.

Cold parts collected condensation, and condensation on a precision race becomes a corrosion site when the pump is idle. Close the machine. Do not store a pulled bearing open on the bench.

Fits that are correct at room temperature are not the running fits at cryogenic temperature. The pump drawing owns that stack-up. This page does not publish a clearance.

The P4 marking on one ring in the photograph is that ring’s marking. It is not a statement that every cryogenic-pump bearing is supplied as P4.

What to send with the inquiry

Write to jin@luoyangsongju.com with the duty and the bearing you need matched.

jin@luoyangsongju.com
  • ▸Fluid: LOX, LIN, LPG, LNG, or the actual composition
  • ▸Pump speed, and temperature from cool-down to steady running
  • ▸Cleanliness and oxygen-compatibility standard, if the fluid can support combustion
  • ▸Whether the motor is on a variable-frequency drive
  • ▸Bore, outside diameter, and the bearing position in the pump
  • ▸Any marking you are trying to match, such as the 7309 marks on the photograph

Questions before you enquire

Can this bearing run in liquid oxygen?

Liquid oxygen is one of the pump media. It is not an approval for your pump. Oxygen service still needs a cleanliness and ignition review.

Is the bearing rated at −196°C?

No. Cold treatment during manufacture, however deep, is not the running temperature.

What is the six-times life?

The stated interval is about six times a conventional bearing. It is not a guarantee, and it is not a factor to apply to another life calculation.

What are 7309P/P4 and 7309PD7F?

Marks on the two rings in the photograph. Dimensions are not given. Confirm the build for your pump at jin@luoyangsongju.com.

Manufacturer quality certificate

Zhongyue’s quality management system is certified to GB/T 19001-2016 / ISO 9001:2015 for the production and sales of bearings. The certificate is held by Luoyang Zhongyue Precision Bearing Co., Ltd. Confirm current validity with the certification body.

Holder
Luoyang Zhongyue Precision Bearing Co., Ltd.
Standard
GB/T 19001-2016 / ISO 9001:2015
Registration no.
626025Q10519R5
Issuer
Kaixin Certification (Beijing) Co., Ltd.
First issue
23 June 2010
Reissue / valid through
30 May 2025 / 7 June 2028
Scope
Production and sales of bearings
ISO 9001:2015 certificate held by Luoyang Zhongyue Precision Bearing Co., Ltd.
English certificate, held by Zhongyue (LYZYC). View large · Download PDF

The Zhongyue plant

Zhongyue runs two campuses, over 46,000 m² in total, with 30,000+ m² of workshops and offices, 150+ people, 400+ bearing machines, and 500+ inspection instruments.

Aerial view of the Zhongyue bearing plant
Two production sites.
Frontage of the Zhongyue bearing plant
Plant frontage.
Gate of the Zhongyue precision bearing plant
Plant gate.
Zhongyue workshop building
Workshop building.

Machines, metrology, and materials

Special-material stock includes bearing steel ZGCr15, stainless 9Cr18 and 9Cr18Mo, high-nitrogen stainless X30 and X40N, and high-temperature steel M50. Heat treatment includes vacuum quenching and a cryogenic treatment step at −196°C. That step is part of manufacture, not a running-temperature rating.

Precision bearing grinding line at Zhongyue
Grinding.
Heat-treatment furnace at Zhongyue
Heat treatment.
Assembly room at Zhongyue
Assembly.
Metrology room at the Zhongyue plant
Metrology.
Bearing test instrument at Zhongyue
Testing.
Coating equipment at Zhongyue
Coating.
Special steel and stainless stock at Zhongyue
Material stock.