Menu
Get a Quote

Custom

Bearings for turbomolecular and dry vacuum pumps

High-speed bearings for turbomolecular pumps and dry pumps, in the materials Zhongyue names. Life depends on the pump, the gas, and the lubrication.

Ball bearing with an orange cage and an outer-ring marking X30, published by Zhongyue for vacuum pumps

Pumps and materials

These bearings are for turbomolecular pumps and dry pumps, where the duty is high speed, low vibration, and long reliable running, often with little lubrication. Rings are a high-nitrogen stainless steel of the Cronidur 30 type, with a special heat treatment and a cold treatment. Balls are hot-isostatic-pressed ceramic. The raceway is finished to a higher precision. Cold treatment is a step in making the rings, not the temperature inside the pump.

The same construction is used where the bearing also sees heat, contamination, or sparse lubrication. Those are operating conditions, not a pass/fail certificate.

The photograph shows a ball bearing with an orange cage. The outer ring is marked X30. That mark belongs to the ring in the picture. It is not a material certificate for every order.

There is no single running-life figure for every pump, gas, and speed. Life is confirmed with the duty.

Published itemWhat it is, and what it is not
PumpsTurbomolecular pumps and dry pumps
RingsHigh-nitrogen stainless of the Cronidur 30 type; special heat treatment and cold treatment
BallsHot-isostatic-pressed ceramic
RacewayDescribed as specially processed and of higher precision
PhotographOrange cage. Outer-ring marking reads X30.
Life numberNot repeated on this page. It is not a universal guarantee.
Cold treatment here is a manufacturing step, the same wording Zhongyue uses on other custom pages. It is not the temperature inside the pump.

Product photographs

Vacuum-pump bearing photograph from Zhongyue, orange cage, outer ring marked X30
Photograph Zhongyue publishes for vacuum-pump bearings. The outer ring is marked X30, and the cage is orange.

Speed, vacuum, and a lubricant that must not spoil the pump

A turbomolecular pump moves gas with a rotor that runs at a speed where the bearing’s DN is the design problem. The bearing is often at the motor end, in a vacuum or in a rough vacuum, with a grease chosen because it does not evaporate into the process. A grease that is fine in a spindle will raise the base pressure of a pump if its oil fraction comes off. Zhongyue does not name the grease. Do not substitute one.

A dry pump is a different duty. There is no sealing liquid, the gas can be hot or corrosive or full of dust, and the bearing may see that gas or be isolated from it by a seal and a grease. “Contamination” and “lack of lubrication” are both on Zhongyue’s list, which is why the material and the raceway are discussed. They do not tell you whether your gas is allowed. Send the gas.

Ceramic balls help at high speed because they are light, and a higher-precision raceway is what Zhongyue says it machines for this line. Neither statement is a residual-unbalance figure or a vibration micron. If the pump maker has a vibration limit, send it.

The old address /products/vacuum-pump-bearings still redirects to the special-purpose page, where this duty was only a short note. This page is the custom category. The redirect is left as it is.

Matching the pump

Say whether the pump is turbomolecular or dry, the rotational speed, the gas, the pressure on the bearing side of the seal, and whether the bearing is grease-lubricated for life or fed with oil. A housing temperature is more useful than the phrase “high speed”.

If the requirement is low outgassing, low magnetic permeability, or a dry-film lubricant instead of grease, write that as a requirement. It is not printed as a standard option on Zhongyue’s page, so it has to be confirmed rather than assumed from the Cronidur sentence.

Corrosion-resistant bearings for other chemical duties remain an inquiry. This page does not absorb them.

Clean assembly

A vacuum bearing is undone by a fingerprint and by the wrong solvent. If the pump specification says the bearing must be free of hydrocarbon film, the preservative that protects an ordinary bearing in transit is itself a contaminant. Agree the cleanliness before the parts ship.

Press on the ring that is being fitted. A small bearing with ceramic balls does not forgive a cocked housing: the ring is stiff in the material and still follows a bore that is out of round.

Do not relubricate a sealed-for-life grease bearing with a shop grease. The original grease was, or should have been, chosen for the vacuum. Adding another grease mixes vapour pressures.

Keep the orange-caged bearing in the photograph distinct from a spindle bearing that happens to look similar. The duty is the pump, and the confirmation is against the pump data.

What to send with the inquiry

Write to jin@luoyangsongju.com with the duty and the bearing you need matched.

jin@luoyangsongju.com
  • ▸Turbomolecular or dry pump, and the maker’s bearing position if you have it
  • ▸Speed and the temperature at the bearing
  • ▸Gas, and whether the bearing is in vacuum, behind a seal, or in the process
  • ▸Grease, oil, or a requirement for no lubricant
  • ▸Bore, outside diameter, and any vibration or outgassing limit
  • ▸Whether the bearing must be cleaned of preservative before packing

Questions before you enquire

Is there a running-life figure?

No single figure covers every pump. Life depends on speed, gas, and lubrication, and it is confirmed with the duty.

What does the X30 mark mean?

It is the marking visible on the outer ring in Zhongyue’s photograph. The page text names a Cronidur 30 type steel for the rings. The photograph is not a material certificate for every order.

Is the cold treatment the operating temperature?

No. It is a process step in making the rings. The pump’s temperature is whatever you measure at the bearing.

Does the old vacuum-pump URL open this page?

No. /products/vacuum-pump-bearings still redirects to the special-purpose page. This category uses a different address on purpose.

Manufacturer quality certificate

Zhongyue’s quality management system is certified to GB/T 19001-2016 / ISO 9001:2015 for the production and sales of bearings. The certificate is held by Luoyang Zhongyue Precision Bearing Co., Ltd. Confirm current validity with the certification body.

Holder
Luoyang Zhongyue Precision Bearing Co., Ltd.
Standard
GB/T 19001-2016 / ISO 9001:2015
Registration no.
626025Q10519R5
Issuer
Kaixin Certification (Beijing) Co., Ltd.
First issue
23 June 2010
Reissue / valid through
30 May 2025 / 7 June 2028
Scope
Production and sales of bearings
ISO 9001:2015 certificate held by Luoyang Zhongyue Precision Bearing Co., Ltd.
English certificate, held by Zhongyue (LYZYC). View large · Download PDF

The Zhongyue plant

Zhongyue runs two campuses, over 46,000 m² in total, with 30,000+ m² of workshops and offices, 150+ people, 400+ bearing machines, and 500+ inspection instruments.

Aerial view of the Zhongyue bearing plant
Two production sites.
Frontage of the Zhongyue bearing plant
Plant frontage.
Gate of the Zhongyue precision bearing plant
Plant gate.
Zhongyue workshop building
Workshop building.

Machines, metrology, and materials

Special-material stock includes bearing steel ZGCr15, stainless 9Cr18 and 9Cr18Mo, high-nitrogen stainless X30 and X40N, and high-temperature steel M50. Heat treatment includes vacuum quenching and a cryogenic treatment step at −196°C. That step is part of manufacture, not a running-temperature rating.

Precision bearing grinding line at Zhongyue
Grinding.
Heat-treatment furnace at Zhongyue
Heat treatment.
Assembly room at Zhongyue
Assembly.
Metrology room at the Zhongyue plant
Metrology.
Bearing test instrument at Zhongyue
Testing.
Coating equipment at Zhongyue
Coating.
Special steel and stainless stock at Zhongyue
Material stock.