Menu
Get a Quote

Custom

Bearings for high-speed wire-rod mills

Bearings for a finishing line that runs fast, takes shock, and stops the whole mill when one ring fails. The steel grade is confirmed for the stand. No life multiple is given.

Cylindrical roller bearing with a separate outer ring, published by Zhongyue for high-speed wire-rod mills

Running duty

These bearings are for a high-speed wire-rod finishing block: continuous running, high speed, and shock at the bite. A failed bearing stops the line.

Ring steel and any life multiple are not stated. Descriptions of this duty do not agree, so neither a steel name nor a life multiple is given. The steel for the stand is confirmed with the inquiry. An older model table on the special-purpose page is a different list and is not the stock list for this bearing.

The rings are given a special heat treatment and a cold treatment, with further material processing and a raceway finished to a higher precision. Cold treatment is part of making the rings, not the running temperature of the mill. There is no model list.

TopicHow this page treats it
DutyContinuous running, high speed, high impact. A failure stops the line.
Steel nameNot stated. Two Zhongyue texts do not use the same name.
Life multipleNot stated. The multiples in those texts do not match, so neither is repeated.
Process words that do not depend on the steel nameSpecial heat treatment, cold treatment, further material processing, a more precise raceway
Model tableNot on the custom page. An older table remains on the special-purpose page and is not copied.
Cold treatment is a manufacturing step. It is not a running temperature for the mill.

Product photographs

Cylindrical roller bearing with a separate outer ring on Zhongyue’s high-speed wire-rod mill page
The image Zhongyue publishes for high-speed wire-rod mill bearings: a cylindrical roller bearing with the outer ring separate.

The finishing block

A high-speed wire-rod block finishes small sections at a speed where the roll neck, the bearing, and the oil system are the limit on the line, not the motor nameplate. The bite is a shock. Between bites the bearing runs continuously, so heat does not get a pause. Water is sprayed on the roll and finds any seal that is tired.

The published image shows a separable outer ring. On a mill that construction often lets the roll be changed while one ring stays on the neck or in the chock. It is a reasonable reading of the photograph. It is not a dimension, and it is not a promise that every bearing offered for this duty is separable. Ask.

Lubrication on these blocks is commonly oil-air or a metered oil mist, because grease will not carry the heat and a flooded housing is hard to seal against water. Zhongyue’s custom page does not name the system. Send the one the block already has. A bearing built for oil-air and then packed with grease runs hot and pushes the grease out.

The cost of a failure is the line, not the bearing. That is why the page talks about unplanned stops. It is also why a life multiple from a brochure is the wrong number to plan a campaign on, especially when a second brochure prints a different multiple. Plan the change from the stand’s history and from the confirmation Zhongyue gives for that neck.

Where it is used

Use this page for a high-speed wire-rod finishing block. The broader steel-plant category, including roughing and slow stands, is on the metallurgy equipment page. Zhongyue’s metallurgy text also mentions wire-rod mills; the detailed conflict of catalogs is handled here by leaving the conflict out.

The special-purpose page still carries an older transcribed table and a different material sentence. Read it as that catalog. Do not add its rows to an inquiry for this page and expect them to be the same product.

The old address /products/wire-rod-mill-bearings still redirects to special-purpose. This category has its own address so that redirect can stay.

Chocks, water, and matched rings

A separable ring must be reassembled with its mate. A campaign of roll changes that mixes outer rings is how internal clearance disappears.

If water has been in the chock, drying the outside of the bearing and putting it back is not a repair. Corrosion under the roller does not show until the next high-speed run.

Do not set a maintenance interval from a life multiple this page refuses to print. Use the mill’s own campaign length, and shorten it when the neck, the oil, or the alignment changes.

Mounting force goes into the ring that is moving. Shock load in service is already high; a brinell from installation becomes the place where the race spalls.

What to send with the inquiry

Write to jin@luoyangsongju.com with the duty and the bearing you need matched.

jin@luoyangsongju.com
  • ▸Block and stand, or the roll-neck drawing number
  • ▸Bore, outside diameter, and width, and whether the outer ring is separate
  • ▸Speed and the nature of the shock at bite
  • ▸Lubrication system already fitted: oil-air, oil mist, circulation, or grease
  • ▸Whether cooling water reaches the bearing
  • ▸The campaign length you run today, and how the last bearing failed

Questions before you enquire

Which steel is it, and how many times longer does it last?

Zhongyue’s custom page and another catalog do not say the same thing. This page states neither the steel nor a life multiple. Both are confirmed for the stand, not copied from a brochure.

Where is the model table?

Not on the custom page. An older table is still on the special-purpose page. It is a different text and it is not merged into this one.

Is this the same product as the metallurgy-equipment bearing?

Related duty, different page. Roughing and general mill work start on the metallurgy page. A high-speed wire-rod block starts here. Songju will say if one inquiry covers both.

Does the old wire-rod URL open this page?

No. /products/wire-rod-mill-bearings still redirects to special-purpose. The custom category is this address.

Manufacturer quality certificate

Zhongyue’s quality management system is certified to GB/T 19001-2016 / ISO 9001:2015 for the production and sales of bearings. The certificate is held by Luoyang Zhongyue Precision Bearing Co., Ltd. Confirm current validity with the certification body.

Holder
Luoyang Zhongyue Precision Bearing Co., Ltd.
Standard
GB/T 19001-2016 / ISO 9001:2015
Registration no.
626025Q10519R5
Issuer
Kaixin Certification (Beijing) Co., Ltd.
First issue
23 June 2010
Reissue / valid through
30 May 2025 / 7 June 2028
Scope
Production and sales of bearings
ISO 9001:2015 certificate held by Luoyang Zhongyue Precision Bearing Co., Ltd.
English certificate, held by Zhongyue (LYZYC). View large · Download PDF

The Zhongyue plant

Zhongyue runs two campuses, over 46,000 m² in total, with 30,000+ m² of workshops and offices, 150+ people, 400+ bearing machines, and 500+ inspection instruments.

Aerial view of the Zhongyue bearing plant
Two production sites.
Frontage of the Zhongyue bearing plant
Plant frontage.
Gate of the Zhongyue precision bearing plant
Plant gate.
Zhongyue workshop building
Workshop building.

Machines, metrology, and materials

Special-material stock includes bearing steel ZGCr15, stainless 9Cr18 and 9Cr18Mo, high-nitrogen stainless X30 and X40N, and high-temperature steel M50. Heat treatment includes vacuum quenching and a cryogenic treatment step at −196°C. That step is part of manufacture, not a running-temperature rating.

Precision bearing grinding line at Zhongyue
Grinding.
Heat-treatment furnace at Zhongyue
Heat treatment.
Assembly room at Zhongyue
Assembly.
Metrology room at the Zhongyue plant
Metrology.
Bearing test instrument at Zhongyue
Testing.
Coating equipment at Zhongyue
Coating.
Special steel and stainless stock at Zhongyue
Material stock.